YOUR WORLDWIDE KITE PARTNER
YOUR WORLDWIDE KITE PARTNER

The Flying Eye – Part 3

Welcome to part 3 of this series about Kite Aerial Photography!

This time, as promised, we will go into some rig construction details.

Rig Construction

The rig has several functions. First, it has to support the camera and the mechanism to trigger it. As we saw in the previous issues, the trigger can be a simple mechanical or electronical timer, which either triggers the camera once or repeatedly with given intervals. For more control, you need a remote control unit. In this case, you will have to place the receiver, the batteries and a servo or electronic switch on the rig. This adds weight which should be well equilibrated to avoid tilting which in turn would result in a horizon which is not … horizontal.

The other function of the rig is to point the camera. Even if the pointing is fixed, you want a t least to be able to change it manually on the ground before launching the rig. So, even if you don’t use a remote control, the basic construction is always the same. The only difference is that in one case you have screws which you fix on the ground and in the other case, these screws are replaced by a motor which is controlled by a remote control (see photos below).

If you are going to motorize an axis, several things need to be observed.

If you want to turn the rig as long as you push some button, you can take any motor you wish and just switch it on and of with your remote control. To know where your camera is pointing, you will have to fix an optical helper on the rig; a bright yellow bar, which can double as the antenna support will do the job. If you want a proportional control, meaning that the position of a potentiometer on your transmitter corresponds to a precise heading for your rig, you won’t need such a helper.

In any case, you should use gears to slow down the rotation and reduce the torque (and power drain) on the motor/servo. For the proportional control, things get a little complicated here. If you know something about remote control servos, you know that their rotation is usually only around 90 degrees. But what you want is 360 degrees (180 in every direction) for your vertical axis. The gears will reduce the possible rotation even more. So you will have to modify your servo … Don’t fear, it’s not as complicated as it seams and it involves more mechanics than electronics. Here are the principles:

The servo knows the position of its axle from a small potentiometer inside it’s housing which is coupled directly to the outgoing axle (photo below). All you have to do is to deceive the electronics by taking the potentiometer out and by coupling it via some more gears to the axle which supports your rig (figure 4). Now the potentiometer will turn 90 degrees when the rig turn 360 degrees … just what we wanted. BUT you must also remove the mechanical stopper inside the servo (figure 5)! Otherwise it won’t rotate freely.

You can do the same thing for the tilting of the camera, but here 90 degrees might be sufficient so you could couple your servo directly to the axle. But buy your servo with metal gears inside and strong enough for the task. In figure 3 you can see that the left gear has lost some teeth because the forces were too high. Another big disadvantage will be a high power drain because this servo will continuously counter the slightest imbalance. Your batteries will be drained faster than you can look! If you can live with that, you can extend the turning range of the servo by modifying the range on the transmitter (figure 6 & 7, below). You just have to replace the existing potentiometer with one of a smaller value and add a small adjustment pot on each side of the main pot. This way you can get a range of ~120°, giving a tilt control from 90° down to 30° up.

How to trigger the camera

The straightforward method is to use a servo to push the button on the camera (figure 8, right). Advantages are: the servo can be simple and cheap; installation is purely mechanical. Disadvantages: mechanical failure is more probable than electronic failure…

The other possibility is an electronic switch, which replaces the servo. This is simple to do with a camera, which has a connector for an electrical remote trigger (figure 9, left). But these connectors are mostly only on the more expensive and heavy models. So if you take a simple and lightweight camera, you will probably have to make your connection yourself. A certain knowledge and skills with electronics are a must to realise this version of the camera trigger. The advantage is its higher reliability.

If you have any questions about KAP, don’t hesitate to contact me or check out one of these sites:

www-archfp.ced.berkeley.edu (archived copy)
kitephotos.com
members.aol.com (archived copy)

These are just a few of many!

Carlo Didier Avatar
Author

Current prize drawing

Djinn VT by Kite Forge (Dec 1st, 2026)

Djinn VT by Kite Forge (Dec 1st, 2026)

Every active subscriber is entered automatically. Subscribers also get the full video tutorial archive, and keep KiteLife flying.

Become a subscriber

Browse by Article Type

Every KiteLife article, sorted by kind. Tap an arrow to open a section.