THE "NO SECRETS" HANDBOOK OF SINGLE LINE KITE TRAINS
by Al Hargus
Most kite trains that I make are constructed in basically the
same manner. Similar materials are used, and construction techniques are the same. In the
first section of this handbook I will give you the basic techniques for constructing any
kite train. In the second section I will give you plans for my favorite kite train
designs, dimensions and specific assembly instructions. Be sure you read the basic
instructions before you begin to assemble any of the kite trains.
I would like to remind you that these designs are, by no means, the only ones you can
make. Literally any kite design or shape of kite can be made to fly in a train of kites,
that is, more than one kite on a single line. Experiment with any design that you think
might make a good train of kites. When you begin to build and fly kite trains your
imagination begins to function in multiples of one. There is no limit to your imagination,
or to the type of kite or the number of kites in a kite train.
This handbook is dedicated to the memory of kite train maker Dave Debolt, without whose
help and inspiration i would have given up on kite train flying many, many years ago.
Basic Materials List
- Materials for the kite sail
a.) Plastic garbage bags (any type of plastic bag will work, colored bags are very
attractive in the sky.)
b.) Tyvek (Spunbonded Olfin can be easily decorated with magic markers or paint, fairly
heavy material per square foot)
c.) Mylar (Colored or silvered, both lightweight and strong)
d.) Paper (Easily decorated, inexpensive, but not very durable)
a.) Most designs use 1/8 inch wood dowel rods.
b.) Bamboo (Very durable, lightweight, but sometimes difficult to locate good bamboo.)
c.) Fiberglass Rods (Strong, but very heavy for its diameter.)
d.) Piano Wire (Can be used for arch trains, about 1/16 inch diameter)
a.) Surveyors Tape (1 inch wide, inexpensive, durable, commonly used at construction
b.) Silk Ribbon (Attractive, easily available, but can be expensive.)
c.) Crepe Paper (2 inch wide, easily available, inexpensive, but not very durable.)
a.) Twisted Nylon or Dacron (Inexpensive, but tends to tangle after repeated use.)
b.) Braided Synthetics (Less stretch, more durable, less tangling, but slightly more
expensive than twisted line.)
c.) Kevlar (Expensive, very strong, very resistant to cutting by other kite line.)
d.) Spectra Line (Expensive, very prone to cutting by other kite line. Because of this
lack of durability and abrasion resistance, Spectra Line IS NOT recommended for
general kite train usage.)
Basic Tools List
a.) Razor Blades or X-acto knife (For cutting kite sails.)
b.) Small saw (For cutting kite spars.)
c.) Tape measure or ruler (For accurate measurements.)
d.) Filament Strapping Tape or Clear Packing Tape. (To secure spars and tails to the
e.) Needle and Thread (Use to secure individual kites to the main flying line.)
f.) Cutting Surface (Material to protect work area when cutting out kite sails.)
g.) Epoxy or Super Glue (Used to secure knots.)
Basic construction techniques
After choosing a sail shape and a train design that you wish to make, you must construct
a template out of cardboard, cut to the shape of your design. Cardboard is readily
available, and is sufficiently durable for kite trains of 25-50 kites. Cardboard does tend
to wear out, producing crooked edges. Use a piece of aluminum plate, if available, or a
thick piece of plastic. Both will last longer and produce straighter edges and will help
to hold down sail material as it is being cut.
Place the template on the material to be used for the sail. Hold pressure on the
template and cut out the material with an X-acto knife or razor blade. (Experiment with a
soldering iron to cut plastics and mylar. Using a hot iron tends to reduce sail tearing
You should be able to cut out 2-4 thickness of material at a time, but you must hold
the template and material firmly. It is suggested that you cut out all the sails before
you go to the next step. If you plan to decorate the sails, do so at this time.
NOTE: Think of kite train construction as an assembly line process. You will do all of
one process for the entire train before going on to the next process. You will become more
proficient at the processes after you do each one hundreds of times.
Spar size and diameter is determined by the size of the kite and the expected winds the
train is to be flown in. Remember that the sail must provide lift for the weight of the
spar. The basic guideline for spar size is: 1/8 inch for up to 18 inch kites (2.5 sq. ft.)
3/16 inch for 36 inch kites (9 sq. ft.) and 1/4 to 1/2 inch for larger kites.
For most kites, a bend must be placed in the spar. (This bend is called
dihedral) Spars should be cut to the size indicated in the instructions. Mark the bend
point as indicated, on each spar. Bundle the spars into groups of about ten (depending on
spar diameter) Place them under hot tap water. After sufficient soaking time place them in
a jig (Use a board with nails. See Diagram #1) Alternatively, place the spars on a board
and weight the ends of the spars to impart a bend into them. Always bend the spars more
than you need. Spars tend to straighten somewhat as they dry. Set the spars aside to dry,
naturally. (Forced drying, hairdryers, etc., tend to split wood rods.)
If you use bamboo, you may want to bend it by passing it through a candle flame or
steam. Caution and patience are required to bend bamboo using these methods.
Attaching Sails to the Spars
Sails are attached to spars with filament strapping tape or clear plastic tape (See
Diagram #2) Clear packing tape is about 2 inches wide and sticks well to plastic. Clear
tape is also very resistant to sun damage (Do not use scotch tape)
Trim the edges of the tape (Neatness counts, even in trains of hundreds of kites.)
Ragged tape edges also catch tails and flying lines. Press and rub down the tape around
the spars; this helps the tape to stick and looks neater.
Securing Kites to the Main Flying Line
There are several methods for securing kites to the main flying line. If you plan to
fly 50 kites or less in your train you can tie pieces of precut and premeasured line to
each kite. Use this line to also tie the spars together. Tie them securely with knots that
If you plan to fly more than 50 kites in your train, mark the selected flying line in
about 3 foot intervals. ( Trains will fly at 3 foot, 5 foot or 20 feet apart, an
arms length of 3-4 feet seems to work best and that length makes easier train
retrieval.) Do not space the kites at less than their own height, as they do not fly well
very close together (i.e. no less that 18 inches apart for 18 inch tall kites) From an
artistic point of view kite trains look best in the air when the kites are closer
Secure the vertical and horizontal spars together with a small piece of line. Secure
the knot with a drop of super glue for safety. Thread the main flying line through the
entire train of kites at the indicated bridle point. You may want to reinforce the spot
where the line passes through the kite with a piece of tape. Move each kite to one of the
marked intervals. Using another line and a needle "sew" the kite to the main
flying line. This method maintains almost total main line strength
NOTE: Knots reduce main line strength by 40-50%. For 25 to 50 -18 inch kites
use 200# test line. For 50 to 100 - 18 inch kites use 300# test line. For 200+ 18 inch
kites use 400# test line.
Als Line Strength Axiom: The strength of the flying line is in
direct proportion to the VALUE of the kite train, not necessarily the pull.
Breakaway kite trains ARE dangerous. SEE SAFETY SECTION.
Securing the Tails to the Kites
Tails provide stability for the kites in a train. The movement of the tails make up a
large portion of the artistic appeal of a train. Use at least two to three times the
height of the kite in tail length. Three or four small pieces are better than one larger
one. Shorter tails tangle less.
The length of the tails is suggested in each kite design in Section Two.
Experimentation is required to match the length of the tails to your prevailing wind
conditions and the artistic look you want for your train.
Tape the tails securely to the bottom point(s) as indicated in the design diagram. Use
the same tape that you used to secure the sail to the spars. It is suggested that you
double the amount and the length of the tails of the last two or three kites at the top of
the train. This increases the stability of the train at the top and keeps the top kites
form tangling too much. (Top kites tend to tangle NO MATTER what you seem to do!)
Construction of a Storage Box
You will need a container to store and transport your train in. The box will not only
be for storage, but neatly arranged kites in the box will launch easier, with less
tangling. Be sure not to have loose box ends or tape in the box that might snag kites as
they are launched.
NOTE: Some kite train fliers spend as much time and artistic energy in making
the storage box for their trains as they take in the actual construction of the train
Flying Techniques for Kite Trains
ALWAYS prepare an anchor for the train BEFORE you launch. A dog screw is
sufficient for up to 50 kites in a moderate wind. For big trains (300+), choose a very
secure anchor. Posts, hydrants, fences or other large secure objects make excellent
NEVER UNDERESTIMATE THE PULL OF A KITE TRAIN, EVEN IN LIGHT
Simply feed out the top kite from the storage box and in moderate winds the kites will launch right from your hand. (5-8 mph is the best wind for
most trains, size and shape of your kite may change this figure) In light winds feed out
15-20 kites down wind and have an assistant hold the top kite, take several steps
backwards and the kites will usually become airborne. In heavy winds be careful so that
the kites do not feed out of the box so fast that they are damaged.
NOTE: Always wear gloves when flying a kite train.
NEVER UNDERESTIMATE THE PULL OF EVEN A SMALL KITE TRAIN.
Some train fliers use a large lift kite at the top of their train to ease in launch (of
a different type than those in their train) The author suggests that you use a larger kite
of the same shape and design as the rest of the kites in your train (i.e., use a 24 inch
wide diamond kite to help an 18 inch diamond kite train). If you choose to use, say, a big
delta instead, be prepared to explain away spectators' questions about the "big"
kite at the top thats holding up all the rest of the train!
Launch site selection and flight control
Kite trains take up a lot of air space; consider this when you choose a flying site.
Plenty of field downwind is preferable in case of an unexpected drop in the wind and the
train comes down. Be aware of other fliers on the field. Once you anchor a train you
cannot move it around easily or quickly. Talk to other fliers on the field about potential
problems. Most will be very accommodating.
About Kite Train Courtesy
Remember that if you have selected Kevlar as your flying line, you can and will cut
most any other kind of kite line that tangles with your train. Be courteous and assist in
untangling the other kite, even if it means bringing down part of your train.
Location of the anchor point is very crucial when flying a train. You may have to move
the anchor point several times before you become familiar with the flying characteristics
of each kite train and with varying wind conditions. Most trains fly at a high angle, and
should be anchored upwind of sport kite fliers, or to the sides of most single line
Fun while flying kite trains
Kite trains attract attention! Be prepared to answer questions about your kite train,
that every spectator seems to ask. How many kites are there? Did you make them? How do you
launch them? How strong is the line?
This is the time to prepare a hand-out for the spectators about yourself, your train,
your local kite club, or your local kite shop. People want to know about your beautiful
kite train, be courteous and tell them. Remember, "NO SECRETS."
Sometimes there will be too much wind to fly a train of more than 25-50 kites. Try
flying your big train in smaller sections side by side. Launch each train and anchor them
about 20-25 feet apart. After observing how the way each train flies, move each anchor
closer together. You can eventually have each train flying mere feet away from each other
in a very spectacular display. Be very careful when you fly trains in this manner, one
tangle can lead to hours of untangling.
As with any strong pulling kite or kite train, you can use your train to pull a wide
variety of spinners, windsocks and banners into the air. Trains have less tendency to
react to gusts of wind and wind changes. Trains are spread out over a wider area of the
wind and are better suited to being used as lifting devices.
Try flying several different shapes of kites together in one train, or try different
sizes of the same shape alternately in the same kite train.
The variety of things for you to do while flying your trains is limited only by your
own imagination. One of the most enjoyable things that you can do while your train is
flying is to simply watch it weave and sway in the winds and marvel at its beauty, a
masterpiece that you created yourself.
Retrieval and landing
An assistant is helpful in kite train retrieval, especially in heavy winds. The
assistant packs the kites away as you pull them in. To assist in heavy wind retrieval, try
securing a metal ring to the main flying line every 25 kites. You will then walk the train
down from the anchor point to the first ring. Hook a strap into the ring and haul the
train back to the anchor point, packing as you move along. When you get the ring to the
anchor, secure the ring and repeat the process until the train is down. Snap clips are
helpful in this retrieval process.
NOTE: Always bring down a kite train BEFORE it gets too windy to retrieve
Bringing a kite train down in light winds uses the same process only faster. When there
is no wind, the train drops to the ground. There is "NO SECRET" that assistants
seem to fade just as the winds did, when you are picking the kites up off the ground.
Kite train safety and Ethics
Remember that even in a light wind a kite train of 200+ kites can develop considerable
pull. (200 kites 18 inch by 18 inch in a 5 mph wind can develop 50 pounds of pull.)
- Never let anyone fool with the flying line or the anchor of a big train.
- Select your anchor carefully. I have dislodged a fire hydrant with a 300 kite train.
- Never allow anyone to pull slack into the main line. Fingers can get wrapped up in
- Always be courteous to other fliers on the same field.
- Never fly near an airport.
- Always use gloves when flying any size kite train.
- Always be courteous to spectators on the field.
- Periodically check the pull of a flying kite train. Be prepared to retrieve the train
before the pull becomes too great.
- Never anchor a kite train and neglect it. Be prepared for emergencies.
- Inspect the flying line after each flight. Breakaways ARE dangerous.
- Be careful of the "Numbers Game". Launch only as many kites as
"YOU" feel safe and comfortable with and can retrieve safely.
Kite train records
As little as 15 years ago the World Record for the most kites on a single line was only
100 kites. As technology and kite train techniques have advanced so has the World Record.
The current official World Record for the "Most Kites on a Single Line" is an
AMAZING 10,567 12 inch by 12 inch kites, flown by Kazuhiko Asaba and the village of
Kamakura, Japan in November of 1991.
More kites than this may have been flown, but to qualify for the World Record you must
retrieve, unbroken all the kites you launch.
There is no limit to the kite train numbers game. The only limit is your imagination
and ingenuity. You just might be the next World Record holder. Good luck and Good Winds.
(Al Hargus personal "Most Kites on a Single Line" record is 326 - 18
inch by 18 inch eddy kites flown in Manistee, Michigan September 15,1989)
Special note of recognition and thanks:
Several of the following kite designs and diagrams originally came from the book
"Kite Train Making" by Eiji Ohashi. The dimensions have been changed, some
measurements have been converted to English and personal modifications have been made to
the designs, but without the work of Eiji Ohashi most of these trains would not have
gotten off the ground. My personal thanks!
About the author
Al Hargus has been flying kites for 22 years. His first homemade kite was a garbage bag
sled made with the help of a friend. Al collects kites of any type, and his present
collection numbers over one thousand.
Al was first introduced to kite trains in 1982, when he attended the American
Kitefliers Association National Convention in Detroit, Michigan. The late Jack Van
Gilders delta kite train became an inspiration for Als many kite trains. Some
of the trains he keeps, many he gives as presents and gifts. He presently has about thirty
kite trains, from ten kites to his largest with over three hundred kites.
He entered his first comprehensive kite contest in Columbus, Ohio in 1983 with a kite
train of one hundred eddy kites. Al has won numerous awards with his kite trains at events
across the country. He currently holds the record for "The Most Kites in a
Train" in Illinois, Michigan, Ohio, Indiana and Pennsylvania.
Al writes the "Tangents and Trivia" column in every issue of KiteLife.com.
FIRST EDITION 1990
REVISED 1991,1992,1996,1998 copyright 1998, Al Hargus